- Removal

Put on gloves to protect your hands.

When prying with a flat-tip screwdriver, wrap it with protective tape, and apply protective tape around the related parts, to prevent damage.

Disconnect the negative (-) battery terminal.

Remove the cluster fascia panel.

(Refer to Body - "Cluster Fascia Panel")

Separate the instrument cluster (A) after loosening the mounting screws.

Remover the instrument cluster (A) after disconnect the cluster connector (B).

- Installation

Install the cluster after connect the cluster connectors.

Install the cluster fascia panel.

Connect the negative (-) battery terminal.

Perform variant coding after exchanging the instrument cluster.

- Inspection

Check point (Warning indicator)

Fault conditions and normal operating conditions, refer to the owner's manual.

No	Ref Symbol	Name	Color	Signal input	Signal Control	Check point
1		Turnsignal (Left)	Green	CAN	BCM (Gateway)	Multifunction Switch BCM CAN Failure
2		Turnsignal (Right)	Green	CAN	BCM (Gateway)	Multifunction Switch BCM CAN Failure
3		Tail Lamp	Green	CAN	BCM (Gateway)	Multifunction Switch BCM CAN Failure
4		Fog Lamp	Green	CAN	BCM (Gateway)	Multifunction Switch BCM CAN Failure
5		High Beam	Blue	CAN	BCM (Gateway)	Multifunction Switch BCM CAN Failure
6		Warning	Yellow	CAN	BSD	BSD System CAN Failure
					TPMS	TPMS System CAN Failure
					SCC	SCC System CAN Failure
					LDWS	LDWS System CAN Failure
					FCW	FCW System CAN Failure
					HBA	HBA System CAN Failure
					BCM	Exterior Lamp BCM CAN Failure
				Hard-wired	Low Washer	Washer fluid level sensor Wiring Failure
				Hard-wired	Digital Input	Reminders when service checks
7		Battery Charge	Red	Hard-wired	Alternator	Alternator Wiring Failure Battery
8		Oil Pressure	Red	Hard-wired	ECM	Oil Pressure Sensor Wiring Failure ECM CAN Failure
9		Check Engine	Yellow	CAN	ECM	ECM CAN Failure
10		Immobilizer	Yellow	CAN + Hard-wired	IMMOBILIZER SMK	Immobilzer System SMK BCM CAN Failure Hard-wired
11		Parking Brake Brake Fluid EBD EPB EVP	Red	CAN	BCM (Gateway) EBD EPB EVP ABS TCS	BCM ABS System EPB System CAN Failure Parking Brake Switch Brake Oil Lever Sensor
12		ABS	Yellow	CAN	ABS	ABS System CAN Failure
13		ESC	Yellow	CAN	TCS	ABS System CAN Failure
14		ESC Off	Yellow	CAN	TCS	ABS System CAN Failure
15		EPB	Yellow	CAN	EPB	EPB System CAN Failure
16		Auto Hold	White Yellow Green	CAN	TCS	TCS System CAN Failure
17		Seat Belt	Red	CAN	BCM (Gateway)	BCM CAN Failure
18		Airbag	Red	CAN	SRSCM	SRSCM System CAN Failure
19		EPS (MDPS)	Red	CAN	MDPS	MDPS Unit System MDPS Motor CAN Failure
20		TPMS	Yellow	CAN	TPMS	TPMS System TPMS Sensor CAN Failure
21		LKAS	Green White Yellow	CAN	LKAS	LKAS System CAN Failure
22		Fuel Warning	Yellow	Direct (Micom)	Fuel Sender	Fuel Sendar Failure Wiring Failure
23		Door Open	Red	CAN	BCM (Gateway)	BCM CAN Failure Door Sensor/switch
24		ECO	Green	Hard-wired	ECO Mode	Drive Mode Switch ECM System TCU System
25		SPORT	Yellow	Hard-wired	SPORT Mode	Drive Mode Switch ECM System TCU System
26		CRUISE	Green	CAN	ECM	ECM CAN Failure
27		SET	Green	CAN	ECM	ECM CAN Failure
28		HBA	Green	CAN	LDWS	HBA System CAN Failure
29		AUTO STOP	Green Yellow	CAN	ECM	ECM CAN Failure
30		AEB	Yellow	CAN	SCC	AEB System CAN Failure

Check point (Gauge)

No	Name	Signal Input	Signal Control (Unit/Sensor)	Check Point
1	Speedometer	C-CAN	ABS/ESC	1) CAN Line failure
3	Tachometer	C-CAN	EMS	1) CAN Line failure
4	Cooling water temperature	C-CAN	EMS	1) CAN Line failure
5	Fuel	Hardwire	Fuel Sander	1) Fuel sender failure
5	Fuel	Hardwire	Fuel Sander	2) Wiring failure
6	Shift lever indicator	C-CAN	TCU	1) CAN Line failure

Diagnosis with GDS

The body electrocal system can be quickly diagnosed failed parts with vehicle diagnostic system (GDS).

The diagnostic system (GDS) provides the following information.
1. Self diagnosis : Checking the failure code (DTC) and display
1. Current data : Checking the system input/output data state
1. Actuator test : Checking the system operation condition
1. Additional function : Other controlling such as he system option and zero point adjustment

Select the 'Car model' and the system to be checked in order to check the vehicle with the tester.

Select the 'Body Control Module (BCM)' to check the 'Cluster Module (CLU)'.

Select the 'Current Data" menu to search the current state of the input/output data.

The input/output data for the sensors corresponding to the cluster module (CLU) can be checked.

To check the input value of cluster illumination, select option "Actuation test".

CLU Variant Coding

After replacing the cluster with a new one, must be performed the "Variant Coding" procedure.

Connect the cable of GDS to the data link connector in driver side crash pad lower panel, turn the power on GDS.

Select model and "BCM".

Select Variant coding mode to perform.

If the trouble codes occurred when performing variant coding, try the CLU variant coding again after checking the installation status of CLU system.

Item	Variant	Part #	Price
Instruments & Gauges · Instrument Cluster	3.5"	94041F3050	$637.89
Instruments & Gauges · Instrument Cluster	4.2"	94061F3080	$1462.55

Instrument Cluster / Carrier