- Replacement

Put on gloves to prevent hand injuries.

When removing with a flat-tip screwdriver or remover, wrap protective tape around the tools to prevent damage to components.

When removing the interior trim pieces, use a plastic panel removal tool not to damage the surface.

Take care not to bend or scratch the trim and panels.

Remove the front door scuff trim.

(Refer to Interior Trim - "Door Scuff Trim")

Remove the hood latch release handle.

(Refer to Hood - "Hood Latch Release Handle")

Carefully remove the front door body side weatherstrip.

Using a screwdriver or remover, remove the cowl side trim (A).

To intall, reverse the removal procedure.

Replace any damaged clips (or pin-type retainers).

- Replacement

Put on gloves to prevent hand injuries.

When removing with a flat-tip screwdriver or remover, wrap protective tape around the tools to prevent damage to components.

When removing the interior trim pieces, use a plastic panel removal tool not to damage the surface.

Take care not to bend or scratch the trim and panels.

Remove the front pillar trim.

To remove the front pillar trim, the fastener remover (A) below must be used.

After slightly lifting up the front pillar trim and putting the tool in, remove the mounting clip (A) by pulling it.

Be sure to replace the existing clips with new ones when removing or replacing the front pillar trim.

Remove the front pillar trim (A).

To intall, reverse the removal procedure.

Replace any damaged clips (or pin-type retainers).

Be sure to replace the existing clips with new ones when removing or replacing the front pillar trim.

- Replacement

[Center pillar lower trim]

Put on gloves to prevent hand injuries.

When removing with a flat-tip screwdriver or remover, wrap protective tape around the tools to prevent damage to components.

When removing the interior trim pieces, use a plastic panel removal tool not to damage the surface.

Take care not to bend or scratch the trim and panels.

Carefully remove the front door body side weatherstrip.

Carefully remove the rear door body side weatherstrip.

Remove the front door scuff trim.

(Refer to Interior Trim - "Door Scuff Trim")

Remove the rear door scuff trim.

(Refer to Interior Trim - "Door Scuff Trim")

Using a screwdriver or remover, remove the center pillar lower trim (A).

To intall, reverse the removal procedure.

Replace any damaged clips (or pin-type retainers).

[Center pillar upper trim]

Put on gloves to prevent hand injuries.

When removing with a flat-tip screwdriver or remover, wrap protective tape around the tools to prevent damage to components.

When removing the interior trim pieces, use a plastic panel removal tool not to damage the surface.

Take care not to bend or scratch the trim and panels.

Remove the center pillar lower trim.

(Refer to Interior Trim - "Center Pillar Trim")

Remove the anchor seat belt connector.

(Refer to Restraint - "Emergency Fastening Device (EFD)")

Using a screwdriver or remover, remove the center pillar upper trim (A).

To intall, reverse the removal procedure.

Replace any damaged clips (or pin-type retainers).

- Replacement

Put on gloves to prevent hand injuries.

When removing with a flat-tip screwdriver or remover, wrap protective tape around the tools to prevent damage to components.

When removing the interior trim pieces, use a plastic panel removal tool not to damage the surface.

Take care not to bend or scratch the trim and panels.

Remove the luggage boad (A).

Remove the tail gate weatherstrip.

Loosen the mounting clips and remove the rear transverse trim (A).

To intall, reverse the removal procedure.

Replace any damaged clips (or pin-type retainers).

- Replacement

Put on gloves to prevent hand injuries.

When removing with a flat-tip screwdriver or remover, wrap protective tape around the tools to prevent damage to components.

When removing the interior trim pieces, use a plastic panel removal tool not to damage the surface.

Take care not to bend or scratch the trim and panels.

Remove the rear seat assembly

(Refer to Rear Seat - "Rear Seat Assembly")

Carefully remove the rear door body side weatherstrip.

Remove the rear door scuff trim.

(Refer to Interior Trim - "Door Scuff Trim")

Remove the rear transverse trim.

(Refer to Interior Trim - "Rear Transverse Trim")

Loosen the mounting clips and screws, remove the luggage partition side trim (A).

After loosening the mounting bolts and screws, remove the luggage side trim (A).

To intall, reverse the removal procedure.

Replace any damaged clips (or pin-type retainers).

- Replacement

Put on gloves to prevent hand injuries.

When removing with a flat-tip screwdriver or remover, wrap protective tape around the tools to prevent damage to components.

When removing the interior trim pieces, use a plastic panel removal tool not to damage the surface.

Take care not to bend or scratch the trim and panels.

Slighty remove the rear door body side weatherstrip.

Remove the rear pillar trim.

To remove the rear pillar trim, the fastener remover (A) below must be used.

After slightly lifting up the rear pillar trim and putting the tool in, remove the mounting clip (A) by pulling it.

Be sure to replace the existing clips with new ones when removing or replacing the rear pillar trim.

Remove the rear pillar trim (A).

Be sure to replace the existing clips (B) with new ones when removing or replacing the rear pillar trim.

To intall, reverse the removal procedure.

Replace any damaged clips (or pin-type retainers).

Trim Panel

- Component Location

- Component Location

- Component Location

- Component Location

- Component Location

- Component Location