The front mounts support the engine at each side. These supports are made of resilient rubber.

REMOVAL
1. Disconnect negative cable from battery.
2. Raise the vehicle.
3. Support the engine.

Left Front Mount-2.5L Engine

Click for full-size image
Right Front Mount-2.5L Engine

Click for full-size image

4. Remove through bolt nut. DO NOT remove the through bolt.
5. Remove the retaining bolts and nuts from the support cushions.
6. Remove the through bolt.
7. Remove the engine mount insulator.

INSTALLATION
1. If the engine support bracket was removed, position the bracket onto the block and install the attaching bolts. Tighten the bolts to 62 Nm (46 ft. lbs.) torque.
2. Place the insulator on the support bracket. Install the insulator retaining bolts and nuts. Tighten the bolts and nuts to 52 Nm (38 ft. lbs.) torque.
3. Install the through bolt and the retaining nut. Tighten the through bolt nut to 69 Nm (51 ft. lbs.) torque.
4. Remove the engine support.
5. Lower the vehicle.
6. Connect negative cable to battery.

A resilient rubber cushion supports the transmission at the rear between the transmission extension housing and the rear support crossmember or skid plate.

REMOVAL
All Transmissions
1. Disconnect negative cable from battery.
2. Raise the vehicle and support the transmission.

Rear Mount (Manual Transmission)

Click for full-size image
Rear Mount (Automatic Transmission)

Click for full-size image

3. Remove the nuts holding the support cushion to the skid plate.
4. Remove the skid plate bolts and the skid plate.

Manual Transmissions
1. Remove nuts holding support cushion to transmission support bracket.
2. Remove the support cushion.
3. Remove bolts holding transmission support bracket to transmission.
4. Remove the transmission support bracket.

Automatic Transmissions
1. Remove nuts holding support cushion to transmission support bracket. Remove the support cushion.
2. Remove the bolts holding the transmission support bracket to transmission.
3. Remove the transmission support bracket.

INSTALLATION
Manual Transmission:
1. Position the transmission mount bracket to the transmission and install the bolts.
2. Tighten the bolts to 54 Nm (40 ft. lbs.) torque.
3. Position the support cushion to the transmission mount bracket and install nuts.
4. Tighten the nuts to 41 Nm (30 ft. lbs.) torque.

Automatic Transmission:
1. Position the transmission mount bracket to the transmission and install the bolts. Tighten the bolts to 54 Nm (40 ft. lbs.) torque.
2. Position the support cushion to the transmission mount bracket and install nuts. Tighten the nuts to 41 Nm (30 ft. lbs.) torque.
3. If the support cushion bracket was removed from the skid plate, position the bracket on the skid plate and install the nuts and bolts. Tighten the nuts to 28 Nm (21 ft. lbs.) torque.

All Transmissions
1. Position the skid plate to the studs of the support cushion and install the nuts. Tighten the nuts to 28 Nm (21 ft. lbs.) torque.
2. Install the skid plate bolts to the sill and tighten to 75 Nm (55 ft. lbs.) torque.
3. Remove the transmission support.
4. Lower the vehicle.
5. Connect negative cable to battery.

Item	Variant	Part #	Price
Front Bracket · On Engine · Right	Engine Mounts, Front	52018696	$0.00
Rear Bracket	Engine Mounts, Rear	52058863	$0.00
Front Mount	Mount	52019276AC	$54.75
Rear Mount	Rear Mount	52058551AB	$0.00

Operation	Task	Skill	Hours
Replace	Front Mount · Left Side	B	0.8
Replace	Front Mount · Right Side	B	0.8
Replace	Rear Mount · Auto Trans	B	0.9
Replace	Rear Mount · Manual Trans	B	0.8

Engine Mount