1. Remove the plug hole plate.
2. Remove the battery cover.
3. Disconnect the negative battery cable.
4. Disconnect the wiring harness.
5. Disconnect the OCV connector.
6. Remove the following parts.
1) Front wheel and tire (RH).
2) Engine under cover and splash shield (RH)
3) Ignition coils.
4) Ventilation hose
5) Cylinder head cover
Click for full-size image
6) Engine front cover lower blind plug
Click for full-size image
7) Engine front cover upper blind plug.
8) Cylinder block lower blind plug.
Click for full-size image
7. Install the SST as shown in the figure.
8. Turn the crankshaft clockwise the crankshaft is in the No. 1 cylinder TDC position (until the balance weight is attached to the SST).
9. Loosen the timing chain.
Click for full-size image
1) Unlock the chain tensioner ratchet using a suitable screwdriver or equivalent tool.
2) Turn the exhaust camshaft clockwise using a suitable wrench on the cast hexagon and loosen the timing chain.
3) Placing the suitable bolt (M6 X 1.0 length 25 mm-35 mm (0.99-1.37 in)) at the engine front cover upper blind plug, secure the chain guide at the position where the tension is released.
Click for full-size image
10. Hold the exhaust camshaft using a suitable wrench on the cast hexagon as shown in the figure.
Click for full-size image
11. Remove the exhaust camshaft sprocket.
Click for full-size image
12. Loosen the camshaft cap bolts in 2-3 passes in the order shown in the figure.
Note: The cylinder head and the camshaft caps are numbered to be reassembled in their original position correctly. When removed, keep the caps with the cylinder head they were removed from. Do not mix the caps.
13. Remove the camshaft.
14. Remove the tappet.
15. Select proper adjustment shim.
New adjustment shim
= Removed shim thickness - Measured valve clearance - Standard valve clearance (IN: 0.25 mm (0.0098 in), EX: 0.30 mm (0.0118 in))
Standard [Engine cold]
IN: 0.22-0.28 mm (0.0087-0.0110 in)
EX: 0.27-0.33 mm (0.0107-0.0129 in)
Click for full-size image
16. Apply the gear oil SAE No. 90 or equivalent) to each journal of the cylinder head as shown in the figure.
17. Install the camshaft with No.1 cylinder aligned with the TDC position.
Click for full-size image
18. Apply the gear oil (SAE No. 90 or equivalent) to each journal of the camshaft as shown in the figure.
Click for full-size image
19. Tighten the camshaft cap bolts in the order shown with the following two steps.
Tightening torque
(1) 5.0-8.0 N-m (51.0-81.5 kgf-cm, 44.3-70.8 in-lbf)
(2) 14-17 N-m (1.43-1.73 kgf-m, 10.4-12.5 ft-lbf)
Click for full-size image
20. Install a new washer.
Click for full-size image
21. Install the exhaust camshaft sprocket.
Note: Do not tighten the bolt for the camshaft sprocket during this step. First confirm the valve timing, then tighten the bolt.
Click for full-size image
22. Install the SST to the camshaft as shown in the figure.
23. Remove the (M6 X 1.0 length 25mm-35mm (0.991.37in)) bolt from the engine front cover to apply tension to the timing chain.
24. Turn the crankshaft clockwise until the crankshaft is in the NO cylinder TDC position (until the balance weight is attached to the SST).
Click for full-size image
25. Hold the exhaust camshaft using a suitable wrench on the cast hexagon as shown in the figure.
26. Tighten the exhaust camshaft sprocket lock bolt.
Tightening torque 69-75 N-m (7.1-7.6 kgf-m, 50.9-55.3 ft-lbf)
27. Remove the SST from the camshaft.
28. Remove the SST from the block lower blind plug.
29. Rotate the crankshaft clockwise two turns until the TDC position. 9 If not aligned, loosen the crankshaft pulley lock bolt and repeat from Step 14.
30. Apply silicone sealant to the engine front cover upper blind plug.
31. Install the following parts.
Click for full-size image
1) Engine front cover upper blind plug.
Tightening torque 8.0-11.5 N-m (82-117 kgf-cm, 71-101 in-lbf)
Click for full-size image
2) Cylinder block lower blind plug.
Tightening torque 18-22 N-m (1.9-2.2 kgf-m, 13.3-16.2 ft-lbf)
Click for full-size image
3) New engine front cover lower blind plug.
Tightening torque 10-14 N-m (102-142 kgf-m, 89-123 in-lbf)
4) Cylinder head cover.
5) Ventilation hose.
6) Ignition coils.
7) Engine under cover and splash shield (RH).
8) Front wheel and tire (RH).
32. Connect the OCV connector.
33. Connect the wiring harness.
34. Connect the negative battery cable.
35. Install the battery cover.
36. Install the plug hole plate.