- Replacement

Put on gloves to prevent hand injuries.

When removing with a flat-tip screwdriver or remover, wrap protective tape around the tools to prevent damage to components.

Use a plastic panel removal tool to remove interior trim pieces without marring the surface.

Take care not to bend or scratch the trim and panels.

Remove the front seat outer shield cover (A) by pulling forward in the direction of the arrow using screw driver or remover.

Disconnect the front seat power switch connector (A).

To intall, reverse the removal procedure.

Make sure the connector is plugged in properly.

Replace any damaged clips (or pin-type retainers).

- Replacement

Put on gloves to prevent hand injuries.

When removing with a flat-tip screwdriver or remover, wrap protective tape around the tools to prevent damage to components.

Use a plastic panel removal tool to remove interior trim pieces without marring the surface.

Take care not to bend or scratch the trim and panels.

Remove the front seat assembly.

(Refer to Front Seat - "Front Seat Assembly")

Loosen the screws and remove the front seat shield inner cover (A).

To intall, reverse the removal procedure.

Replace any damaged clips (or pin-type retainers).

- Replacement

Put on gloves to prevent hand injuries.

When removing with a flat-tip screwdriver or remover, wrap protective tape around the tools to prevent damage to components.

Use a plastic panel removal tool to remove interior trim pieces without marring the surface.

Take care not to bend or scratch the trim and panels.

Remove the front seat assembly.

(Refer to Front Seat - "Front Seat Assembly")

Remove the front seat shield outer cover.

(Refer to Front Seat - "Front Seat Shield Outer Cover")

Remove the front seat shield inner cover.

(Refer to Front Seat - "Front Seat Shield Inner Cover")

Remove the front seat lower protector (A).

Loosen the mounting screws and remove the airbag wiring (A).

Push the lock pin, remove the front seat headrest (A).

Remove the front seat back board (A).
1. Seperate the upper back cover by pushing the lock pin in the direction of the arrow.
1. Remove the front seat back cover by lifting in the direction.

Turn the front seat back cover inside out. Then pull out the headrest guides (A) while pinching both side of the lower part of the guides, and remove them.

Disconnect the front air ventilation duct (A).

[Upper]

[Lower]

Remove the protector (A) from the front seat back frame.

After removing the Velcro tape (A) and hog-ring clips (B) inside the front seat back cover, remove the seat back cover (C).

Be careful not to allow the sponge insert wire to separated in its place.

To intall, reverse the removal procedure.

Make sure that the connectors are connected completely

Replace any damaged clips (or pin-type retainers).

To prevent wrinkles, make sure that the cover (B) is stretched evenly before connecting the hog-ring clips (A).

Replace the hog-ring clips with new ones using special tool (C) (09880-4F000).

- Replacement

Put on gloves to prevent hand injuries.

When removing with a flat-tip screwdriver or remover, wrap protective tape around the tools to prevent damage to components.

Use a plastic panel removal tool to remove interior trim pieces without marring the surface.

Take care not to bend or scratch the trim and panels.

Remove the front seat assembly.

(Refer to Front Seat - "Front Seat Assembly")

Remove the front seat shield inner cover.

(Refer to Front Seat - "Front Seat Inner Cover")

Remove the front seat shield outer cover.

(Refer to Front Seat - "Front Seat Outer Cover")

Remove the front seat lower protector (A).

Separate the clip and remove the air ventilation duct (A).

Disconnect the front seat motor connectors (A).

Remove the protector (A) from the front seat cushion frame.

[Center]

[LH]

[RH]

Remove the front seat cushion cover (A) from the front seat cushion frame.

After removing the Velcro tape (A) and hog-ring clips (B) inside the front seat cushion cover, remove the seat cushion cover (C).

Be careful not to allow the sponge insert wire to separated in its place.

To intall, reverse the removal procedure.

Make sure that the connectors are connected completely

Replace any damaged clips (or pin-type retainers).

To prevent wrinkles, make sure that the cover (B) is stretched evenly before connecting the hog-ring clips (A).

Replace the hog-ring clips with new ones using special tool (C) (09880-4F000).

- Replacement

[LH]

Put on gloves to prevent hand injuries.

When removing with a flat-tip screwdriver or remover, wrap protective tape around the tools to prevent damage to components.

When removing the interior trim pieces, use a plastic panel removal tool not to damage the surface.

Take care not to bend or scratch the trim and panels.

Remove the rear seat assembly [LH].

(Refer to Rear Seat - "Rear Seat Assembly")

Push the lock pins, and remove the rear seat headrest (A).

Using a screwdriver or remover, remove the cap (A).

Using a screwdriver or remover, remove the rear seat back cover (A).

Pull out the rear seat headrest guides (A) while pinching both sides of the lower part of the guides, and remove them.

Remove the rear seat back cover assembly (A) from the rear seat back frame.

After removing the Velcro tape (A) and hog-ring clips (B) inside the rea7r seat cushion cover, remove the seat cushion cover (C).

To intall, reverse the removal procedure.

Make sure that the connectors are connected completely

Replace any damaged clips (or pin-type retainers).

To prevent wrinkles, make sure that the cover (B) is stretched evenly before connecting the hog-ring clips (A).

Replace the hog-ring clips with new ones using special tool (C) (09880-4F000).

[RH]

Put on gloves to prevent hand injuries.

When removing with a flat-tip screwdriver or remover, wrap protective tape around the tools to prevent damage to components.

When removing the interior trim pieces, use a plastic panel removal tool not to damage the surface.

Take care not to bend or scratch the trim and panels.

Remove the rear seat assembly [RH].

(Refer to Rear Seat - "Rear Seat Assembly")

Remove the rear back armrest.

(Refer to Rear Seat - "Rear Back Armrest")

Push the lock pins, and remove the rear seat headrest (A).

Using a screwdriver or remover, remove the cap (A).

Using a screwdriver or remover, remove the rear seat back cover (A).

Remove the rear seat armrest board (A).

Pull out the rear seat headrest guides (A) while pinching both sides of the lower part of the guides, and remove them.

Remove the rear seat back cover assembly (A) from the rear seat back frame.

After removing the Velcro tape (A) and hog-ring clips (B) inside the rear seat cushion cover, remove the seat cushion cover (C).

To intall, reverse the removal procedure.

Make sure that the connectors are connected completely.

Replace any damaged clips (or pin-type retainers).

To prevent wrinkles, make sure that the cover (B) is stretched evenly before connecting the hog-ring clips (A).

Replace the hog-ring clips with new ones using special tool (C) (09880-4F000).

- Replacement

Put on gloves to prevent hand injuries.

When removing with a flat-tip screwdriver or remover, wrap protective tape around the tools to prevent damage to components.

When removing the interior trim pieces, use a plastic panel removal tool not to damage the surface.

Take care not to bend or scratch the trim and panels.

Remove the seat cushion assembly.

(Refer to Rear Seat - "Rear Seat Assembly")

After removing the Velcro tape (A) and hog-ring clips (B) inside the rear seat cushion cover, remove the seat cushion cover (C).

[Front side]

[Rear side]

To intall, reverse the removal procedure.

Make sure that the connectors are connected completely.

Replace any damaged clips (or pin-type retainers).

To prevent wrinkles, make sure that the cover (B) is stretched evenly before connecting the hog-ring clips (A).

Replace the hog-ring clips with new ones using special tool (C) (09880-4F000).

Seat Cover

- Component Location

- Component Location

- Component Location

- Component Location

- Component Location

- Component Location