Document ID: 1816965

Step	Action	Yes	No
DEFINITION: After completing a turn, extra steering input is required for the steering wheel to return to center.
1	Did you review the Power Steering System Description and Operation and perform the necessary inspections?	Go to Step 2	Go to Symptoms - Power Steering System
2	Verify that poor return of the steering wheel is present. Does the system operate normally?	System OK	Go to Step 3
3	Raise and support the vehicle. Lifting and Jacking the Vehicle Lubricate the tie rod ends and ball joints, if applicable. Inspect the suspension system for worn or damaged components. Repair as necessary. Did you find and correct the condition?	Go to Step 12	Go to Step 4
4	Rotate the steering wheel ONE revolution in both directions. Rotate the steering wheel back to the original position. Was the steering wheel abnormally difficult to rotate in either direction?	Go to Step 5	Go to Step 10
5	Note: Position the wheels straight ahead. Do NOT rotate the steering wheel more than one complete revolution from center. Disconnect the intermediate shaft from the steering column. Note the position of the steering wheel and rotate the steering wheel ONE revolution in both directions. Rotate the steering wheel back to the original position. Was the steering wheel abnormally difficult to rotate in either direction?	Go to Step 11	Go to Step 6
6	Inspect the intermediate shaft for stiff or loose joints. Repair or replace as necessary. Did you find and complete the repair?	Go to Step 12	Go to Step 7
7	Remove the front tire and wheel assemblies. Tire and Wheel Removal and Installation Disconnect both outer tie rod ends from the steering knuckles. Use your hands in order to move the tie rod end studs. If abnormally difficult to move, replace the tie rod end. If equipped with recirculating ball steering, ensure that idler and pitman arm joints are not to stiff. Repair as necessary. Did you find and complete the repair?	Go to Step 12	Go to Step 8
8	Use your hands to rotate the steering knuckle inboard and outboard in order to inspect for a binding strut bearings, ball joints, or axle. Repair or replace any abnormally stiff or loose components. Did you find and complete the repair?	Go to Step 12	Go to Step 9
9	Inspect for binding in the steering gear. If a binding is present, repair or replace the steering gear. Did you find and complete the repair?	Go to Step 12	Go to Step 10
10	Inspect the wheel alignment and adjust as necessary. Wheel Alignment Measurement Did you find and complete the repair?	Go to Step 12	—
11	Inspect the steering column for a binding. If a binding is present, repair or replace the steering column as necessary. Did you find and complete the repair?	Go to Step 12	—
12	Operate the system in order to verify the repair. Did you correct the condition?	System OK	—

Document ID: 2422253

Special Tools

GE-28431-6 - Fluorescent Dye

For equivalent regional tools, refer to Special Tools.

Note:

If fluid is found on a manual steering gear or on an electronic power steering gear, do not replace steering gear. Vehicles equipped with these systems do not use hydraulic power steering fluid. The fluid may be assembly fluid or another system fluid.
Clean the components and identify the sources of the leaks before attempting to repair or replace any power steering components. Clearly mark all locations of leaks with paint, marker, or equivalent for warranty identification and engineering root cause analysis.

Some customers may comment on a fluid LEAK or NOISY power steering pump. Upon inspection, the technician may find power steering fluid leaking from the hydraulic power steering system. Use the following inspection procedure in order to diagnose the source of the leak and take appropriate action to correct the condition.

Inspect the fluid level in the power steering fluid reservoir. Refer to Checking and Adding Power Steering Fluid. If the fluid level is NOT low, a careful analysis of the condition is necessary to confirm that the type of fluid is actually power steering fluid.
Visually inspect the power steering system and components where the fluid has accumulated.

Caution: Do not clean using brake cleaner or other reactive solvents as these solvents can damage rubber gaskets, seals and bushings.

Use a clean towel or a rag in order to completely clean off all residual fluid from the power steering components.
Add 30 cc (1 oz) of GE-28431-6 - dye to the power steering fluid.
Start the vehicle and warm the steering system by turning to the left steering stop and to the right steering stop 10 times with the weight of the vehicle on the front tires.
Turn vehicle engine OFF.
Shine a black light on the area where the residual fluid accumulated. Identify the sources of the leaks.
Mark all locations of leaks with paint, marker, or equivalent.
Repair or replace all affected components.

Document ID: 2211186

Figure 1: Rack and Pinion System

Test Description

The numbers below refer to the step numbers on the diagnostic table.

This step tests the system for restrictions.
This step tests the following components for the following conditions:

The pump for internal leaks
The power steering pipes for kinks

This step tests the ability of the pump to regulate flow at maximum pressure.
This step tests the ability of the pump to regulate flow under normal operating conditions.
This step tests the internal components of the pump and the gear.

Step	Action	Value(s)	Yes	No
DEFINITION: The Power Steering System Test Procedure will perform the following functions: Test the operation of the hydraulic power steering system. Test the operation of the power steering pump and power steering gear. Identify restrictions in the system.
1	Inspect the power steering fluid for the following indications of contamination: Milky fluid - water Brown fluid - burnt Debris in fluid - plastic or dirt Is the fluid free of contamination?	—	Go to Step 3	Go to Step 2
2	Flush the power steering system. Refer to Power Steering System Flushing. Did you complete the procedure?	—	Go to Step 3	—
3	Note: In order to accurately diagnose the system, the malfunction must be present during the test procedure. Attempt to duplicate the condition. Is the condition present?	—	Go to Step 4	System OK
4	Turn the ignition switch to the OFF position. Place a drain pan under the vehicle in order to catch any power steering fluid. Disconnect the power steering pressure pipe/hose from the power steering pump or the power steering gear as necessary. Install the J-44721 - Power Steering System Analyzer . Fill the power steering system. Refer to Checking and Adding Power Steering Fluid. Did you complete the installation?	—	Go to Step 5	—
5	Fully open the J-44721 - Power Steering System Analyzer valve. Start the engine. Caution: Do not hold the steering wheel in the full turn position longer than 5 seconds, as damage to the steering pump may result. Turn the steering wheel and BRIEFLY hold the steering wheel against the steering stop in order to release any trapped air from the system. Inspect and ensure that all of the power steering pipe/hose connections are not leaking. Making sure the steering wheel is OFF the steering stop, observe the pressure reading. Is the pressure reading greater than the specified value?	1379 kPa (200 psi)	Go to Step 6	Go to Step 7
6	Note: A restriction may be present in the power steering system. Turn OFF the engine IMMEDIATELY. Locate and repair the restriction. Did you complete the repair?	—	Go to Step 15	—
7	Allow the engine to run until the engine reaches full operating temperature. Record the pressure reading and flow reading. Partially close the J-44721 - Power Steering System Analyzer valve until the system pressure reaches the specified value, then record the FLOW reading. Subtract second flow reading from the first flow reading. Is the flow DECREASE greater than 3.8 L (1 gal) per minute?	4827 kPa (700 psi)	Go to Step 11	Go to Step 8
8	Note: Do not leave the valve closed for more than 5 seconds, or internal pump damage could accrue. Fully close then open the J-44721 - Power Steering System Analyzer valve 3 times. Record all of the high pressure readings. Refer to Power Steering Pump Specifications for power steering system pressure relief specifications. Are the 3 high pressure readings within specifications?	—	Go to Step 9	Go to Step 13
9	Are the three high pressure readings within 245 kPa (50 psi) of each other?	—	Go to Step 10	Go to Step 13
10	Increase the engine speed to approximately 1,500 RPM. Record the flow reading. Refer to Power Steering Pump Specifications for power steering system pressure specifications. Is the actual flow reading within specifications?	—	Go to Step 11	Go to Step 13
11	Is the difference between the actual flow reading and the maximum flow specification more than 3.8 L (1 gal) per minute?	—	Go to Step 13	Go to Step 12
12	Turn the steering wheel from steering stop to steering stop and record the FLOW readings at each stop. Is the flow LOWER than 3.8 L (1 gal) per minute?	—	Go to Step 15	Go to Step 14
13	Replace the power steering pump. Refer to Power Steering Pump Replacement. Did you complete the replacement?	—	Go to Step 15	—
14	The power steering gear is leaking across the piston or bypassing the valve circuit. Replace the power steering gear. Refer to Steering Gear Replacement. Did you complete the replacement?	—	Go to Step 15	—
15	Test the power steering system for the original condition. Does the original condition still exist?	—	Go to Step 5	Go to Step 16
16	Disconnect and remove the J-44721 - Power Steering System Analyzer from the vehicle. Connect the vehicle power steering pipes/hoses. Fill and bleed the power steering system. Refer to Power Steering System Bleeding. Did you complete the procedure?	—	System OK	—

Document ID: 2673039

Step	Action	Yes	No
1	Did you review the Power Steering System Description and Operation and perform the necessary inspections?	Go to Step 2	Go to Symptoms - Power Steering System
2	Verify that a rattle, clunk or shudder noise is present. Is a rattle, clunk or shudder noise present?	Go to Step 3	System OK
3	Inspect the power steering hoses for proper routing and clearance. Is the routing or clearance of a power steering hose incorrect?	Go to Step 11	Go to Step 4
4	Inspect the engine drive belt for cracking or excessive wear. Refer to Drive Belt Falls Off and Excessive Wear Diagnosis. Is the drive belt cracked or excessively worn?	Go to Step 12	Go to Step 5
5	Inspect the power steering pump pulley for damage. Is the power steering pump pulley damaged?	Go to Step 13	Go to Step 6
6	Inspect the power steering pump for the proper installation. Refer to Power Steering Pump Replacement. Is the power steering pump installation incorrect?	Go to Step 14	Go to Step 7
7	Inspect the steering gear for the proper installation. Refer to Steering Gear Replacement. Is the steering gear installation incorrect?	Go to Step 15	Go to Step 8
8	Inspect in the inner tie rods and the outer tie rods for looseness. Refer to Steering Linkage Inner Tie Rod Inspection and to Steering Linkage Outer Tie Rod Inspection. Are the inner tie rods or the outer tie rods loose?	Go to Step 16	Go to Step 9
9	Inspect the front suspension. Refer to Noise Diagnosis - Front Suspension. Is the front suspension worn?	Go to Step 17	Go to Step 10
10	Inspect the intermediate steering shaft. Is the intermediate steering shaft worn?	Go to Step 18	Go to Step 3
11	Adjust or replace the hose that is causing the noise. Refer to the appropriate procedure: Fluid Cooler Outlet Hose Replacement Power Steering Fluid Reservoir Outlet Hose Replacement Power Steering Gear Inlet Pipe/Hose Replacement Power Steering Gear Outlet Pipe/Hose Replacement Did you complete the repair?	Go to Step 19	—
12	Replace the drive belt. Refer to Drive Belt Replacement. Did you complete the repair?	Go to Step 19	—
13	Replace the power steering pump pulley. Refer to Power Steering Pump Pulley Replacement. Did you complete the repair?	Go to Step 19	—
14	Install the power steering pump correctly. Refer to Power Steering Pump Replacement. Did you complete the repair?	Go to Step 19	—
15	Install the power steering gear correctly. Refer to Steering Gear Replacement. Did you complete the repair?	Go to Step 19	—
16	Replace either the worn inner tie rod or the worn outer tie rod. Refer to Steering Linkage Inner Tie Rod Replacement or to Steering Linkage Outer Tie Rod Replacement. Did you complete the repair?	Go to Step 19	—
17	Replace the worn front suspension component. Did you complete the repair?	Go to Step 19	—
18	Replace the intermediate steering shaft. Refer to Intermediate Steering Shaft Replacement. Did you complete the repair?	Go to Step 19	—
19	Operate the system in order to verify the repair. Did you correct the condition?	System OK	Go to Step 3

Document ID: 2250749

Step	Action	Yes	No
1	Did you review the Power Steering System Description and Operation and perform the necessary inspections?	Go to Step 2	Go to Symptoms - Steering Wheel and Column
2	Verify a rattle noise is present by driving the vehicle on a rough road. Verify a clunk noise is present by turning the steering wheel to the left and to the right several times with the key in the ON position. Is a rattle or a clunk noise present?	Go to Step 3	System OK
3	Inspect the steering gear for the proper installation. Is the steering gear installation incorrect?	Go to Step 6	Go to Step 4
4	Inspect the intermediate steering shaft. Is the intermediate steering shaft worn?	Go to Step 8	Go to Step 5
5	Inspect the front suspension. Refer to Noise Diagnosis - Front Suspension. Is the front suspension worn?	Go to Step 7	Go to Step 3
6	Install the steering gear correctly. Refer to Steering Gear Replacement. Did you complete the repair?	Go to Step 9	—
7	Replace the worn front suspension component that is causing the noise. Did you complete the repair?	Go to Step 9	—
8	Replace the intermediate steering shaft. Refer to Intermediate Steering Shaft Replacement. Did you complete the repair?	Go to Step 9	—
9	Operate the system in order to verify the repair. Did you correct the condition?	System OK	Go to Step 3

Document ID: 1774873

Step	Action	Yes	No
1	Did you review the Power Steering System General Description and perform the necessary inspections?	Go to Step 2	Go to Symptoms - Power Steering System
2	Verify that the steering effort is hard or too easy in one or both directions. Does the system operate normally?	System OK	Go to Step 3
3	Perform the power steering test procedure. Refer to Power Steering System Test. Did you complete the procedure?	Go to Step 4	—
4	Operate the system in order to verify the repair. Did you correct the condition?	System OK	Go to Step 3

Document ID: 2757380

Condition	Action
The battery power is low.	Ensure proper battery voltage.
The intermediate shaft dash seal is binding.	Adjust the dash seal or replace the intermediate shaft if necessary. Refer to Intermediate Steering Shaft Replacement.
The intermediate shaft joints are loose or worn.	Inspect the joints and the pinch bolts for damage, and replace the intermediate shaft if necessary. Refer to Intermediate Steering Shaft Replacement.
The steering gear is binding.	If necessary, inspect and replace the steering gear. Refer to Steering Gear Replacement.
The upper steering shaft is bent.	If necessary, replace the steering column. Refer to Steering Column Replacement.
The connectors to the assist motor are damaged or disconnected.	Verify the connectors are properly connected. Verify the connectors are not damaged. If the connectors are damaged, replace the connectors.
The sensor wire is damaged.	Replace the steering gear. Refer to Steering Gear Replacement.
The controller is malfunctioning.	Confirm the DTC. If necessary, replace the steering gear. Refer to Steering Gear Replacement.
The motor shaft is binding.	Confirm the DTC. If necessary, replace the steering gear. Refer to Steering Gear Replacement.

Document ID: 1774865

Condition	Action
The steering column mounting bolts are loose.	Tighten the pivot bolt and the mounting bolts to specification.
The steering gear is loosely mounted.	Tighten the steering gear mounting bolts to specification.
The tie rod ends are loose or damaged.	If necessary, inspect for damage and replace the tie rod ends. Refer to Steering Linkage Outer Tie Rod Replacement.

Document ID: 2759583

Step	Action	Yes	No
1	Did you review the Power Steering System Description and Operation and perform the necessary inspections?	Go to Step 2	Go to Symptoms - Power Steering System
2	Verify that the steering wheel surges or jerks while turning. Does the steering wheel surge or jerk while turning?	Go to Step 3	System OK
3	Inspect the front suspension for worn or binding components. Did you find and correct the condition?	Go to Step 15	Go to Step 4
4	Raise and support the vehicle. Refer to Lifting and Jacking the Vehicle. Inspect the steering linkage outer tie rod for wear or a binding condition. Is the steering linkage outer tie rod worn or binding?	Go to Step 10	Go to Step 5
5	Inspect the intermediate steering shaft for wear or a binding condition. Is the intermediate steering shaft worn or binding?	Go to Step 11	Go to Step 6
6	Inspect the steering gear for wear or a binding condition. Is the steering gear worn or binding?	Go to Step 12	Go to Step 7
7	Inspect the steering column for wear or a binding condition. Is the steering column worn or binding?	Go to Step 13	Go to Step 8
8	Inspect the power steering assist motor for an indication of excessive heat. Does the power steering assist motor appear to be overheated?	Go to Step 9	Go to Step 14
9	Note: Do not perform excessive parking lot maneuvers during testing. Excessive parking lot maneuvers can cause the power steering motor to heat up. Allow the power steering motor to cool and retest the system. Did you correct the condition?	Go to Step 15	Go to Step 14
10	Replace the steering linkage outer tie rod. Refer to Steering Linkage Outer Tie Rod Replacement. Did you complete the repair?	Go to Step 15	—
11	Replace the intermediate steering shaft. Refer to Intermediate Steering Shaft Replacement. Did you complete the repair?	Go to Step 15	—
12	Replace the steering gear. Refer to Steering Gear Replacement. Did you complete the repair?	Go to Step 15	—
13	Replace the steering column. Refer to Steering Column Replacement. Did you complete the repair?	Go to Step 15	—
14	Replace the steering gear. Refer to Steering Gear Replacement. Did you complete the repair?	Go to Step 15	—
15	Operate the system in order to verify the repair. Did you correct the condition?	System OK	Go to Step 3

Document ID: 2400914

Note: Review the system description and operation in order to familiarize yourself with the system functions. Refer to Power Steering System Description and Operation.

Visual/Physical Inspection

Inspect for aftermarket devices which could affect the operation of the power steering system.
Inspect the easily accessible or visible system components for obvious damage or conditions which could cause the symptom.
If equipped with hydraulic power steering, inspect for leaking power steering components. If necessary, refer to Power Steering Fluid Leaks.
If equipped with hydraulic power steering, verify the power steering fluid level is correct. Refer to Checking and Adding Power Steering Fluid.
If equipped with hydraulic power steering, inspect the power steering fluid for the following indications of contamination:

Milky fluid – water
Brown fluid – burnt
Debris in fluid – plastic or dirt

If the hydraulic power steering system is contaminated, flush the power steering system. Refer to Power Steering System Flushing.

Symptoms List

Refer to a symptom diagnostic procedure from the following list in order to diagnose the symptom:

Document ID: 2759707

Step	Action	Yes	No
Special Tools CH-39570 - Chassis Ear For equivalent regional tools, refer to Special Tools.
1	Did you review the Power Steering System Description and Operation, check fluid level and perform the necessary inspections?	Go to Step 2	Go to Symptoms - Power Steering System
2	Verify that a whine or growl noise is present with the engine running. Is a whine or growl noise present?	Go to Step 3	System OK
3	Verify that a whine or growl noise is present with the engine off while turning the steering wheel. Is a whine or growl noise present?	Go to Step 7	Go to Step 4
4	Inspect the power steering fluid for the following indications of contamination: Milky fluid – water Brown Fluid – burnt Debris in fluid – plastic or dirt Is the fluid free of contamination?	Go to Step 14	Go to Step 5
5	Flush the power steering system. Refer to Power Steering System Flushing. Did you complete the procedure?	Go to Step 6	—
6	Operate the system in order to verify the repair. Did you correct the condition?	System OK	Go to Step 14
7	Inspect the power steering gear fasteners for looseness. Is the steering gear loose?	Go to Step 20	Go to Step 8
8	Inspect the steering gear for loose or worn bushings. Are the steering gear bushings loose or worn?	Go to Step 21	Go to Step 9
9	Verify that steering column dash outer seal is in position. Is the steering column dash outer seal damaged or out of position?	Go to Step 22	Go to Step 10
10	Verify that steering column dash inner seal is in position. Is the steering column dash inner seal damaged or out of position?	Go to Step 23	Go to Step 11
11	Disconnect the outer tie rods and individually turn the steering knuckle assembly right to left. Refer to Steering Linkage Outer Tie Rod Replacement. Is a whine or growl noise present?	Go to Step 12	Go to Step 13
12	Disconnect the lower ball joints from the steering knuckle and rotate the steering knuckle and strut. Refer to Front Lower Control Front Arm Replacement and Front Lower Control Rear Arm Replacement. Is the whine or growl present?	Go to Step 24	Go to Step 25
13	Note: Position the wheels straight ahead. Do NOT rotate the steering wheel more than one complete revolution from center for this procedure. Disconnect the intermediate shaft from the steering column. Refer to Intermediate Steering Shaft Replacement. Note the position of the steering wheel and rotate the steering wheel ONE revolution in both directions. Rotate the steering wheel back to the original position. Is the whine or growl present?	Go to Symptoms - Steering Wheel and Column	—
14	Using the CH-39570 - ear , inspect the power steering hoses for a whine or growl noise. Is the noise present at the power steering hoses?	Go to Step 17	Go to Step 15
15	Using the CH-39570 - ear , inspect the power steering gear for a whine or growl noise. Is the noise present at the power steering gear?	Go to Step 18	Go to Step 16
16	Using the CH-39570 - ear , inspect the power steering pump for a whine or growl noise. Is the noise present at the power steering pump?	Go to Step 19	Go to Step 1
17	Check the hoses for damage or ground outs. Adjust the routing of the power steering hoses or replace if damaged. Did you complete the repair?	Go to Step 26	—
18	Replace the power steering gear. Refer to Steering Gear Replacement. Did you complete the repair?	Go to Step 26	—
19	Replace the power steering pump. Refer to Power Steering Pump Replacement. Did you complete the repair?	Go to Step 26	—
20	Replace the power steering gear fasteners. Refer to Steering Gear Replacement. Did you complete the repair?	Go to Step 26	—
21	Replace the power steering gear bushings. Did you complete the repair?	Go to Step 26	—
22	Reposition or replace the steering column dash outer seal. Did you complete the repair?	Go to Step 26	—
23	Reposition or replace the steering column dash inner seal. Did you complete the repair?	Go to Step 26	—
24	Replace the strut top mount. Refer to Strut, Strut Component, or Spring Replacement. Did you complete the repair?	Go to Step 26	—
25	Replace the front lower control front arm or the front lower control rear arm. Refer to Front Lower Control Rear Arm Replacement and Front Lower Control Front Arm Replacement. Did you complete the repair?	Go to Step 26	—
26	Operate the system in order to verify the repair. Did you correct the condition?	System OK	Go to Step 1

Document ID: 2759607

Step	Action	Yes	No
Special Tools CH-39570 - Chassis Ear For equivalent regional tools, refer to Special Tools.
1	Did you review the Power Steering System Description and Operation and perform the necessary inspections?	Go to Step 2	Go to Symptoms - Power Steering System
2	Verify that a whine or growl noise is present. Is the steering gear quiet?	System OK	Go to Step 3
3	Perform the Diagnostic System Check — Vehicle. Refer to Diagnostic System Check - Vehicle Are any codes present?	Go to Diagnostic Trouble Code (DTC) List - Vehicle	Go to Step 4
4	Inspect the power steering gear fasteners for looseness. Is the steering gear loose?	Go to Step 13	Go to Step 5
5	Inspect the power steering gear for loose or worn bushings. Are the steering gear bushings loose or worn?	Go to Step 14	Go to Step 6
6	Verify that steering column dash outer seal is in position. Is the steering column dash outer seal damaged or out of position?	Go to Step 15	Go to Step 7
7	Verify that steering column dash inner seal is in position. Is the steering column dash inner seal damaged or out of position?	Go to Step 16	Go to Step 8
8	Inspect the power steering motor for a whine or growl noise using the CH-39570 - ear . Is the noise present at the power steering motor?	Go to Step 19	Go to Step 9
9	Inspect the power steering gear for a whine or growl noise using the CH-39570 - ear . Is the noise present at the power steering gear?	Go to Step 20	Go to Step 10
10	Disconnect the outer tie rods, refer to Steering Linkage Outer Tie Rod Replacement, and individually turn the steering knuckle assembly right to left. Is a whine or growl noise present?	Go to Step 11	Go to Step 12
11	Disconnect the lower ball joints from the steering knuckle , refer to Front Lower Control Rear Arm Replacement and Front Lower Control Front Arm Replacement, and rotate the steering knuckle and strut. Is a whine or growl noise present?	Go to Step 17	Go to Step 18
12	Note: Position the wheels straight ahead. Do NOT rotate the steering wheel more than one complete revolution from center for this procedure. Disconnect the intermediate shaft from the steering column, refer to Intermediate Steering Shaft Replacement. Note the position of the steering wheel and rotate the steering wheel ONE revolution in both directions. Rotate the steering wheel back to the original position. Is a whine or growl noise present?	Go to Symptoms - Steering Wheel and Column	Go to Step 20
13	Replace the power steering gear fasteners. Refer to Steering Gear Replacement. Did you complete the repair?	Go to Step 21	—
14	Replace the power steering gear bushings. Did you complete the repair?	Go to Step 21	—
15	Reposition or replace the steering column dash outer seal. Did you complete the repair?	Go to Step 21	—
16	Reposition or replace the steering column dash inner seal. Did you complete the repair?	Go to Step 21	—
17	Replace the strut top mount. Refer to Strut, Strut Component, or Spring Replacement. Did you complete the repair?	Go to Step 21	—
18	Replace the front lower control front arm or the front lower control rear arm. Refer to Front Lower Control Rear Arm Replacement and Front Lower Control Front Arm Replacement. Did you complete the repair?	Go to Step 21	—
19	Replace the power steering gear. Refer to Steering Gear Replacement. Did you complete the repair?	Go to Step 21	—
20	Replace the power steering gear. Refer to Steering Gear Replacement. Did you complete the repair?	Go to Step 21	—
21	Operate the system in order to verify the repair. Did you correct the condition?	System OK	Go to Step 2

Steering

Related components